Milwaukee Home Builder | Getting Specific
Great nation, we’re back with more excitement, a job optimizing for the homebuilders. So today we’re gonna talk about cutting stairs, triggers and I’m talking about more specifically into the job built stringer, which means it’s like a sort of standard stair that goes from a first floor and second floor from first sort of a basement one that gets covered in carpet down the road. Basically just a no frills seriously. What this will be, his just a straight run, no, uh, no landing. Milwaukee Home Builder We can go over a what that would look like in future podcasts, but for this episode we’re just going to go ahead and talk about cutting corners and then this could go for that set of stairs as well. So you name it pretty much says this will be your go to for a cutting stairs period. Um, so first thing that I want to talk about is, is this episode you’ll need and uh,
few of the tools that you’ll be, it will be, I’m obviously a tape measure, a level, a framing square, a calculator, pencil or some sort of marketing tool. You’ll definitely want to have a circular saw. Milwaukee Home Builder Some saw horses and chances are I will probably add to this list as we, uh, as we go. So Milwaukee homebuilders is what we’re optimizing for. And without further ado, let’s get into the process of laying upstairs and actually cutting the stair stringers. Here we go. So here we go. First thing you’re going to do is figure out what your, you know, the, the total drop is going to be from the top of the finished floor or whatever the top of the deck height, whatever, whatever it is that you’re putting a stairs off of. So for instance, if you’re doing a stairs on a
firm base, first photo basement, you want to make sure you know what your, um, your finished floor is going to be on your first floor because of it’s just osb right now from the framing, but you’re going to add, if it’s going to be a three quarter inch hardwood floor, well that’s going to be the, you know, add three quarters of an inch to your finished floor. Milwaukee Home Builder So let’s say you had a measurement of 100 inches from the finished floor to the basement floor. Now you’re going to be 103 quarters and that is pretty important because if you don’t figure that in your, uh, measurement is going to be off and you won’t be able to pass inspection that way. So that being said, you know, your finished floor dimension, the obits carpet, that’s basically a zero. It doesn’t add anything to the dimension co-advise anyways. So to keep that in mind, make sure you have your final dimensions figured into your, your overall height for the stairs.
No, when you’re doing this, you want to make sure that you’re measuring where the stairs are going to sit. And what I mean by this is if you don’t measure, like, let’s say you’re doing a basement floor and you measure from, you know, just straight down from where the, uh, the finished floor is. Now though, Milwaukee Home Builder
vertically down, there’s a good chance that you’re going to be off because a lot of times based and floors are not perfectly level. Um, you know, so that you could have a pitch going from, from where you measured to where the direction that says, do you want to make sure you actually use a laser to carry out your final dimension or you know, just level out and measure that way one way or another. You want to make sure you measure from where your first step is. I was here, uh, so where the stairs are going to set the easiest way to figure this out. Basically you’re going to do some rough calculations. Let’s say you’re a measurement is 100 inches from where you’re measuring. Now all of your, you’re right. This has to be the same height that further in Wisconsin, Milwaukee Home Builder they have to be within three eighths of an inch of each other, which is pretty easy if you ask me, but either way you’re going to figure out what your, um, you know, overall I was going to be in the height of the riots, has to be within seven and eight inches. So you can’t be any less than seven inches, but it can’t be any more than eight inches on a standard stairway. So Milwaukee home builder,
so we’ll just take our 100 inch dimension that those are rough measurements. We’ll divide that by two divided by 12 and do a number that gives us. But basically we’re going to keep dividing it by different number until we get a number between seven and eight. Basically once you know that the number that you divided up into a hundred. So let’s say you got to take 14 steps to get you a number between seven and eight. Okay? So you’re going to have 17 prizes. What that means is there’s going to be over. When you’re rises, we step up and take it from the bottom floor up to the top floor. And every rise also has a run that was actually stepping on. So basically the serpents and step on tread surface has or friends have to be a minimum night is. So for every rise you have to have an equal run, Milwaukee Home Builder equal amount of run. So you have 14 rises, you’re going to have 14 ron, and if you’re run is nine inches, you’re going to be. You’re going to have 14 times nine years. There’s going to be from the point, you know, stairway opening for
pretty, uh, pretty simple calculations, but hang some people up every once in a while, Milwaukee Home Builder so you want to make sure that you think through it and get it right the first time. The other thing to keep in mind though is the first floor that you’re stepping on that is also considered a run. So if you have 14 rises, technically you only have 13 actually steps because the 14th ron is the finished floor. So just keep that in mind when you’re doing your math could get a little confusing from time to time.
So once you get your rough dimensions and then to go roughly how far out you’re coming with your stairway, then you can get the exact dimension and they do the same process one last time and make sure that you’re doing based off of the exact height and the height off of the floor just where the opening is. And that seems like an extra step on the Istep, but it’s actually pretty important to. You want to make sure that you take the time to do that right. Lucky home builders,
so don’t skip that mixture. You can do it. Next thing you would want to do is pull out the straightest two by 12 that you got for the stairway flora. It’s getting pretty common now to use LPL stringers or given lsl is basically a version of the script to 11 and a quarter inches. Basically people are using these because they’re straighter and they’re stronger. They won’t warp and twist. So it’s just a, in my opinion, a good way to go for straight years now is a lot more consistent. So just my opinion, but that’s what I would recommend. Milwaukee Home Builder
So if you’re using a standard two by 12, I want to make sure you find the straightest one, you Adam. Milwaukee Home Builder Um, but if you use another lsl or an Lpl, they should be very straight or within little bits of each other so you don’t have to worry about it quite as much. I still always double check. I was given a quick site, um, before I started laying out or cutting because you never know there are manmade product so they can have flaws. Do you want to make sure that you eliminate as much as possible? All politics is a 32nd site to make sure everything good. I think it’s worth it. So lucky home builders.
Recent Comments