Remodeling Milwaukee | Lots of options
Toradora hung and oceans cut off and everything I think we’re going to step into how to how to trim it out. You don’t put the casing on it and make it look pretty we’re going to go through everything from selecting the right trim to suck in the right size of trim. You know whether you want stained trim, painted, trim or or exactly what we’re going with so first things. First, we’re going to you don’t decide on what style you like it and I like if you like, Remodeling Milwaukee traditional in a ranch styleflat, you know, what’s a little bit around over the outside, about a half inch wider thicker than the the inside, where you actually nail remodeling, milwaukee, okay, so then we’re also going to let you know. Sometimes people like what’s considered to be more colonial, just got to look at my profile to it. It’s typically got about three bumps in a square edge for no putting it in simplest, possible terms.
Young there’s there’s wider colonial standard casings about two and a quarter inches wide and go up from there to as wide as you want really the, but the standard next step up is 3 or 3/4, sometimes 3 and 1/2 they’re all about the same price point you just get you know, depending on the manufacturer, that’s going to be there upgraded size of casing. So that being said, there’s also, you know like the square style or seeing a lot more. Like he’s just a real simple look:sometimes people miter it still. Remodeling Milwaukee Some people just do a no square top, no matter what people do, love a square top, no matter, but you don’t want to hang out past the the sides about a half inch give or take some times. He will go with a thicker and wider top so that it’s got definition all the way around it. Endless options, when, when you’re talking casing we’re going to just stick to the more standard size like two and a quarter to three and quarter for this instructional. So once you have your, you know the style you want picked out you’re going to want to look at what color you want. You know. Do you want white painted, you know a different color painted do you want staind. Do you want us to lacquer finish where you can see the to the green still, but it’s more of a pain than a stain can kind of play with it and see their match the rest, your house, or make a statement with the particular dory or you’re working on staind?
You know when we’re talking about this. Just for ease of knowledge. Now, let’s say we’re hanging out we’re going to be casing the door with trina quarter. Casing you going to want to make sure you know if you’re setting the door on hardwood or the casing and hardwood or tile and only sort of solid floor, Remodeling Milwaukee that’s not that carpet or not going to be cut off at a later date. This life flooring underneath you going to want to take your your door side, which is typically about 90 in sometimes more depending on manufacturer and you’re, going to want to trim the the bottom edge squares. Whatever is going to be coming into contact with the floor is going to take him. Put that on a you know, like a miter, saw something of that nature and can just cut it. Square make sure it’s a nice clean-cut. Sometimes the factory edges just did it don’t look very nice or even older. Sometimes we’ve seen them or they’re still the chainsaw cut from for the wood was mailed. You see all types of stuff when, when your been doing it as long as we have so long story, short I just want to make that square. Remodeling Milwaukee Make a nice clean-cut so that when it contacts the floor, it’ll be like a nice clean good fit once you get both of those, you know one for each each side of the door and we can repeat the same exact steps for the opposite side of the door. So we’ll focus on just one for now:you’re going to want to kind of figure out what kind of margin between you know the edge of the casing and the edge of the jam you want. Typically, we go about three sixteenths of an inch in from the edge of the gym so meeting the inside edge, where the the door kind of rests in you know where the door door stops, are nailed to that’s what we consider the inside edge. So some people prefer to measure their their margins to make sure that it’s consistent all the way around you can just take a block of wood and put in a 3/16 notch and see if a nice consistent place, you can keep the marking in a lot of different ways. You can do it, but will say:you’ll just take the block mark through the 3/16 margin on the top corner on each side and two spots in the middle and in the very bottom edge. That way, you get the most consistent margins possible once you’ve done, that you can set your door casing tight down to the floor, making sure there’s no gaps and you’re going to go back up to the top corner of each side of the door and find where your 3/16 margin marks are. Are you going to put a mark on the actual casing? Edge for that and that’s going to be working to put your miter so long story short, you put your mark margins there. So you know where to what length to cut the piece. So you, when you put your top piece on, it’s got the right margin same as the the sides. Typically, we use to use a dewalt, 10in miter saw with high tooth blade.
We use the the freud brand they’re, just usually thicker they’re, better blades, they last longer. They they cut smoother, probably going to be a little bit cheaper, blade or less teeth, as if it’s thinner, we do a lot. Remodeling Milwaukee What would they call in the industry? Blade wobble, meaning that the the cut itself? Is it going to be perfectly smooth? There’s going to be steps in it from where the blade actually pushes off to the side, and sometimes you can’t even see the wobble with your eyes. You got to feel it when you’re, when you’re in youtube, you topping your side together. It’s going to it’s going to show up as a black line that you can’t get to go. Away. Some people use some wood putty to fill it in and just ignore. It would rather get a perfectly fight tight fit, so we use better, saw blades to start with and then that alleviate a lot of the bs stepped cuts on the ones that we usually use are around a hundred bucks give or take. But you know it’s it’s pennies to to pay considering how much time it saves us from our miter, spitting, nice and tight. The. First try so I want to get your saw setup in your your blade on there and get your casing sides already too. To cut.
Will they make it always make sure that when you’re cutting casing or you want the the fattest, the thickest part of the casing, tight to the fence? Reason being is, if you, if you go thinner part, the the sauce has a tendency to have Remodeling Milwaukee awesome fraying of the the wood fibers on the profile as it’s cutting it. It’s just the way, the the geometrics of the the song the blade. Are you just what happens not a whole lot? You can do to get around it other than putting the thickest part of the casing uptight to the saw. So when you’re cutting the left side, you going to going to belleville to turn the side of a 45 degree angle to the left and seem going for the the right once you’ve done that you don’t want to go nice and nice and slow through the cut. You don’t want to just jam it down because you’re going to going to get a lot of blow out with the the saw blade you want a nice clean-cut for that, so we’ll just take it. Take it nice and easy and make yourself a smooth cut. Remodeling Milwaukee Once we get through the the piece we actually use on hand planer hand block plane to fine-tune the cut, even though we use the expensive blades, we can still get it even more perfect with a blog playing the ones that we use are made by veritas. It’s a canadian company in but good things to say about those planes are the blades are really really hard, so they don’t sell out as fast on the tickle a bit longer to sharpen but too small a small price to pay for for quality
Recent Comments